If your key fob is fine, but you need to replace your BMW key fob battery, you’ll need a CR2032 battery. These small batteries are sometimes referred to as “watch batteries,” and you’ll want to make sure you’re using the right size.Just remove the key fob cover, carefully remove the old BMW key fob battery, and place the new one in gently. Free Download BMW INPA F & E Series Install on Win XP/7/8/10; Download 06.2017 BMW ISTA-D 4.05.32 Standalone (NEW) INPA vs ISTA+: ISTA+ better, INPA easier; BMW ISTA+ 4.09.33 Standalone SQLiteDB’s Download Free; BMW ICOM A2 clone K-line problem (fixed) Best bmw computer diagnostic and programming tool for bmw service center.
»Back To BMW IndexBMW 3-Series - Key Remote Programming
How To Program Bmw Key Fob E90 Plane Crash
Three methods to try:
Method 1:
1. Working from within the vehicle and with the doors shut
2. Turn ignition to position 1 and back to off within 5 seconds.
3. Remove the key from ignition and press and hold the unlock button for 15seconds during this time press the key lock button 3 times within 5 seconds.
4. Release both buttons.
5. Doors will lock and unlock to show correct programming hasoccurred.
How To Program Bmw Key Fob E90 Plane Car
Method 2:
To do this procedure you need to have one working key and one key that needs tobe programmed.
1) Get in and close all doors.
2) Turn on the ignition and turn off quickly. (No more than 5 seconds) to startthe process. Next action must take place within 30 seconds.
3) Remove the 1st key.
4) Hold the key up near your left shoulder (this is so it is closer to the remotereceiver antenna.
5) Hold down the unlock button and press the lock button 3 times. Release theunlock button and the doors lock which confirms the operation.
6) Quickly repeat steps 4 & 5 for key #2 etc.
If it does not work, try doing the keys in opposite order. Key 2 then key 1, vs 1then 2.
Method 3:
Alternate if you do not have a working remote
How To Program Bmw E90 Key Fob
1. Turn key to position 1 five times very quickly 2. Remove key 3. Hold unlockbutton then press lock button 3 times, release unlock button.
How To Program Bmw Key Fob E90
4. If you have another key do the same button pressing within 30 seconds 5. Turnon ignition to finalise.
PLEASE NOTE: This programming procedure programs the remote control part of thekey. Any transponder chip for the immobiliser (starting of car) will not be programmed and must be done by aspecialist.
REMOTE CONTROL PROGRAMMING INSTRUCTION FOR BMW - DIAMOND SHAPED KEY.
THESE INSTRUCTION ARE SUITABLE FOR BMW E46, E39, X3, X5 AND OTHERS PRODUCED FROM 1999.
OEM PART NUMBER OF KEYS : KR55WK47993 AND OTHERS. NO TOOLS REQUIRED.
1. Insert key into driver’s door lock and open central locking system using the car key. You must initiate the central locking system first. |
2. Get into the car, close all doors and insert the key into the Ignition Switch. |
3. Using the car key, switch the ignition lock briefly to ignition lock position 1 and switch off again. The switching time must remain under 5 seconds, otherwise the system is not ready for initialization. You must insert & turn the key to ignition switch position 1 ( not position 2 ) |
4. Remove the key from Ignition Switch. |
5. Press button #2 and hold in. You must remove the key from ignition switch andpress & holdbutton #2 within 5 seconds of removal. |
5. Still pressing button #2 - press button #1 three times. You then have up to 10 seconds to press the Roundel button THREE times. |
6. Relase button #2 When done properly the doors will automatically lock and then unlock. |
7. Test remote ( s ) to ensure proper programming. |
If you have any additional remote keys - you start their programming on STEP 5.
Do not insert any additional remote key into the ignition switch - if you do - the 1st key will lose it's programming.
If the ZV does not send a return signal, initialization bust be restarted. Once the first initialization process has been completed,
another three radio transmitters can be initialized. For every radio transmitter, the procedure described under 4 above must
be repeated within 30 seconds, otherwise initialization stand-by is switched off. During initialization, all other existing radio
transmitters must be initialized. The ignition lock must never be reactivated during the initialization process. If this were to
hapen, then all radio transmitters would have to be re-initialized.
How To Program Bmw Key Fob
SIMILAR TOPICS :
How To Program Bmw Key Fob E90 Plane Parts
- BMW - 'rubber', old ( produced to 1999) key remote programming instruction